Dodge Ram 2004 Скачать руководство пользователя страница 423 | Manualshive

Страница: 423 / 642

background image

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Ignition Switch harness connector.
Measure the resistance between ground and the Fused B(+) circuit.
Is the resistance below 10K ohms?

All

Yes

→

Repair the Fused B(+) circuit for a short to ground and replace the
fuse.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Replace the Blower Motor and fuse in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition on.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Using a 12-volt test light connected to ground, back probe the Blower Motor Feed
circuit in the Blower Motor harness connector.
Does the test light illuminate brightly?

All

Yes

→

Go To

6

No

→

Go To

9

6

Turn the ignition off.
Connect a jumper wire between ground and the Blower Motor High Driver circuit in
the Blower Motor harness connector.
Turn the ignition on.
Does the blower motor run at high speed?

All

Yes

→

Go To

7

No

→

Replace the Blower Motor in accordance with the Service Infor-
mation.
Perform BODY VERIFICATION TEST - VER 1.

7

Turn the ignition off.
Disconnect the A/C - Heater Control Module C2 harness connector.
Disconnect the Blower Motor harness connector.
Measure the resistance of the Blower Motor High Driver circuit between the A/C -
Heater Control Module C2 harness connector and the Blower Motor harness
connector.
Is the resistance below 5.0 ohms?

All

Yes

→

Go To

8

No

→

Repair the Blower Motor High Driver circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

8

Turn the ignition off.
Disconnect the A/C - Heater Control Module C2 harness connector.
Measure the resistance between ground and the Ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

→

Replace the A/C - Heater Control Module in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.

409

HEATING & A/C

*BLOWER MOTOR INOPERATIVE —

Continued

«
...
421
422
423
424
425
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Kargo Master Страницы: 5

GRAND CHEROKEE 2023

Бренд: Jeep Страницы: 108

Бренд: Vauxhall Страницы: 323

Бренд: Pacbrake Страницы: 14

Бренд: Camcar Страницы: 6

Бренд: ABL Страницы: 4

2008 MX-5 Miata

Бренд: Mazda Страницы: 400

Бренд: Chevrolet Страницы: 344

Бренд: Prorack Страницы: 15

Бренд: Kuda Страницы: 3

2012 Truck Chassis cab

Бренд: RAM Страницы: 506

Бренд: ideus Страницы: 159

Бренд: Sears Страницы: 41

Бренд: Easee Страницы: 12

FOLDING TOP 1971

Бренд: Fisher Body Страницы: 37

Бренд: Manik Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: INDIWORK Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды