Dodge Ram 2004 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 642

background image

Symptom:

NO CLUSTER MESSAGE

When Monitored and Set Condition:

NO CLUSTER MESSAGE

When Monitored:

With ignition on, the ACM monitors the PCI Bus for a message from

the MIC containing the airbag warning indicator status. The MIC transmits the message
one time at ignition on, lamp state change, or in response to the ACM message.

Set Condition:

If the MIC message is not received for 10 consecutive seconds, the code

will set.

POSSIBLE CAUSES

MIC, COMMUNICATION FAILURE

ACM, NO CLUSTER MESSAGES

STORED CODE OR INTERMITTENT CONDITION

ACTIVE CODE PRESENT

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:

All

ACM - ACTIVE DTC

Go To

2

ACM - STORED DTC

Go To

4

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

2

Turn the ignition on.
With the DRBIII

t

, ensure PCI Bus communications with the Instrument Cluster.

Is the Instrument Cluster communicating on the PCI Bus?

All

Yes

→

Go To

3

No

→

Refer to category COMMUNICATION CATEGORY and select the
related symptom NO RESPONSE or INSTRUMENT CLUSTER
BUS +/- SIGNAL OPEN.
Perform __AIRBAG VERIFICATION TEST - VER 1.

96

AIRBAG

«
...
108
109
110
111
112
...
»

Содержание Ram 2004



































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ram 2004

Бренд: Vauxhall Страницы: 199

Бренд: Pyle Страницы: 4

MagicComfort MSH200

Бренд: Waeco Страницы: 108

Бренд: Tusk Страницы: 2

PRIME DESIGN VRR-NV200

Бренд: Safe Fleet Страницы: 12

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: FALCON RIDGE Страницы: 8

Бренд: Scosche Страницы: 8

Dodge Challenger SRT8®Challenger SRT8 392 2012

Бренд: Dodge Страницы: 5

Бренд: Edelbrock Страницы: 2

Бренд: Skoda Страницы: 165

Бренд: Thule Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 56

Бренд: Mopar Страницы: 17

Prime Design OCM-3032

Бренд: Safe Fleet Страницы: 4

PRIME DESIGN HRR3-E-PM52

Бренд: Safe Fleet Страницы: 12

Бренд: Volkswagen Страницы: 68

1995 C/K Pickup

Бренд: Chevrolet Страницы: 483

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды