Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 61

Страница: 61 / 72

MAINTENANCE

Active Regeneration

The “Regen Settings” are set to “Uninhibit

Regen” (Default setting) in the Utilities menu.

This will allow active regeneration to occur if

the system detects the exhaust temperatures

are insufficient to passively keep the DPF from

clogging with particulates. The engine controls

inject diesel fuel directly into the DPF to

increase temperature to burn off, i.e. clean, the

soot captured in the filter.
This should occur infrequently, but will happen

more often if the engine is allowed to idle

excessively (longer than five minutes) or

sawing is lightly loaded. Failure to change oil at

recommended intervals can also contribute to

excessive soot buildup. It is not unusual to see

excessive smoke being emitted from the

tailpipe during regeneration. . Machine

operation is NOT interrupted. It is

recommended to let the regeneration complete

automatically, typically 20 minutes, but if it

needs to be interrupted turn the ignition to

STOP

CAUTION

ACTIVE REGENERATION will cause the

exhaust temperatures to be extremely high.

Ensure exhaust will not come into contact

with combustible materials

During active regeneration the display panel

will show the red status icon, Engine Exhaust

High Temperature Lamp.
This type of regeneration corresponds to Level

2 status. If the Regen Settings” in the Utilities

menu are set to “Inhibit Regen” and a Level 1

pop-up message was cancelled, then a series

of two orange Level 2 pop-up messages will

appear on the control screen:

Regeneration Level 2 Orange Caution

Screen 1

Regeneration Level 2 Orange Caution

Screen 2

When this pop-up message appears, the

operator can choose one of three options:
1. Cancel out of the regeneration process and

continue operations.

Change the “Regen Settings” in the Utilities

menu to “Uninhibit Regen” which will allow

for an active regen to take place. The

regeneration process will typically take 20

minutes to complete. This option will also

allow for the continued use of the machine

without any further action from the

operator

. However, the operator must be

aware that the exhaust temperatures will
be extremely high.

Move the machine to a safe location and

conduct a Parked Regeneration. This

option is recommended as long as time

permits.

Parked Regeneration

When the diesel particulate levels in the DPF

become too high, a red Level 3 pop-up

message will appear on the control screen:

Regeneration Level 3 Red Caution

Screen 1

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 61 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: