manualshive.com logo in svg

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 36 / 72

Поделиться
Скачать
Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 36

 

OPERATING 

Water Supply 

The water supply directs cooling water to the 

fuel cooler and blade and minimizes dust when 

cutting.   

Using the Water Supply 

The saw is equipped with an “Automatic Water 

System” (AWS). A solenoid valve in the system 

works in conjunction with the “Zero Blade” 

option on the control panel.  When the saw 

blade is “zeroed” at the pavement surface, the 

solenoid valve will allow water to flow when the 

blade is lowered into a cut. When the blade is 

raised out of the cut and the blade passes the 

“zero” point, the water flow will automatically 

shut off. 
1.  Connect the water source hose to the 

water supply hose connection on the rear 

of the saw. 

 

Water Supply Hose Connection 

2.  Connect water supply hose (72”) extending 

from the front of the upright assembly to 

the manifold on the blade guard. 

3.  Move the water valve lever on the control 

panel forward to start the flow of water to 

the AWS. When finished cutting, shut off 

water supply to the blade guard by pulling 

the valve to the 

OFF

 position, shut off 

water supply at source and remove source 

hose from the saw.  

NOTE: When using AWS, adjust the water 
valve lever to meter the water flow. AWS will 
automatically turn the water on/off when the 
blade enters or exits the cut. 

Water Control Valve 

4.  During cold weather, drain water from the 

lines in accordance with the maintenance 

section of this manual. 

Water Pump 

The water pump (optional item) directs water 

from the water source hose to the saw blade. 
1.  Ensure all water supply lines are 

connected. 

2.  Ensure that the water valve located on the 

control panel is in the “OFF” position. 

3.  Turn on the water pump switch to start the 

pump. DO NOT start the water pump until 

just before cutting. DO NOT leave the 

water pump on when the cutting task is 

complete to avoid draining the battery. 

4.  Push the water valve to the “ON” position.  

5.  When cutting is complete, move the water 

valve to the “OFF” position. 

6.  Turn off the water pump switch OFF to stop 

the pump. 

Cutting 

Cutting Guides

 

Use the cutting guides as needed to help 

follow the cutting line. Always check the cutting 

guides for proper alignment with the blade prior 

to cutting. 

Adjusting the Front Pointer 

1.  Remove the lanyard from the cable cleat. 

2.  Lower the front pointer frame to the ground. 

3.  Loosen both front pointer frame screws. 

4.  Divide an 8–10 ft. piece of string in half. 

5.  Place the looped end of string into a gullet 

on the backside of the blade. 

36

Содержание CORE CUT CC9074DC-36









































































Отзывы:

Нет отзывов