Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 34

Страница: 34 / 72

OPERATING

Optional Blade Arbor Configurations

Three additional blade arbor configurations are

available on the CC9074DKV Deep Cut saw.

•

Louie Arbor

•

Storm Arbor

•

Roger Arbor

The “Louie” arbor configuration is provided on

all flanges 7” and larger. It consists of a series

of four dowel pin holes located on a Ø3” bolt

circle around the blade flange bolt. There are

eight dowel pins provided in the tool storage

case located on the fuel tank to use for this

option.

“Louie Arbor”

The “Storm” arbor configuration is provided on

all flanges 8” and larger. It consists of six

3/8”-16 bolt holes located on a Ø4-1/2” bolt

circle around the blade flange bolt. There are

twelve 3/8”-16 flat head cap screws and a hex

key provided in the tool storage case located

on the fuel tank to use for this option.

“Storm Arbor”

The “Roger” arbor configuration is provided on

all flanges 9” and larger. It is the same as the

“Storm” arbor except, the 3/8”-16 holes are

located on a Ø6” bolt circle around the blade

flange bolt. There are twelve 3/8”-16 flat head

cap screws and a hex key provided in the tool

storage case located on the fuel tank to use for

this option.

“Roger Arbor”

When using any of the optional blade arbor

configurations, a Ø1” arbor pin is available to

assist with installation of the blade. The arbor

pin is provided in the tool storage case located

on the fuel tank. The arbor pin is placed into

the center blade shaft hole and the blade is

placed on it. The pin will allow the operator to

align the blade while securing with the screws

using the optional “Storm” or “Roger” arbor

configurations. To remove the arbor pin,

thread the flange bolt halfway into the pin and

manually pull the pin out.

Engine

WARNING

Operate the saw in well-ventilated

areas. Concentrated engine

exhaust can cause loss of

consciousness and/or death.

DO NOT touch the engine/muffler with the

engine running, and always let them cool

down prior to touching or servicing the

saw.

DO NOT leave the saw unattended while the

engine is running

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 34 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: