manualshive.com logo in svg

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 43 / 72

Поделиться
Скачать
Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 43

 

 

MAINTENANCE 

Daily Service 
Check Engine Oil Level 

Prior to checking the engine oil level, ensure 

that there is no blade installed on the saw and 

that the saw frame is in a level position. 
1.  Remove the engine oil dipstick from the 

starter side of the engine. (Between the 

engine and saw upright assembly) 

Engine Oil Dipstick 

2.  Check the oil level on the dipstick. The 

level should be between the two round 

marks. 

Engine Oil Level Indicators 

3.  If the level is low, remove the engine oil fill 

cap located on the left side of the saw just 

below and to the rear of the diesel 

particulate filter (DPF). 

 

Engine Oil Fill Cap 

4.  Add oil until the level is correct. 

5.  Replace the engine oil fill cap. 

Check Fuel Level 

Prior to checking the fuel level, ensure that 

there is no blade installed on the saw and that 

the saw frame is in a level position. 
1.  With the ignition switch in the ON position, 

scroll through the display until the Home 

screen appears. The fuel level gauge will 

be displayed in the lower center of the 

control display. 

2.  If fuel level is low, remove the fuel tank fill 

cap located on the left side of the upright 

assembly. 

Fuel Tank Fill Cap 

3.  Fill the fuel tank with ultra-low sulfur diesel 

fuel only. 

Hydraulic System 

WARNING 

Always place a piece of 

cardboard or paper up 

against hydraulic 

components, or use a leak detection fluid 

to check for hydraulic fluid leaks. Keep 

all body parts away from leaks and/or 

areas that may eject hydraulic fluid. 

Pressurized hydraulic fluid can penetrate 

the skin, causing serious injuries. Seek 

medical attention immediately! 

Always make sure any hydraulic 

components being serviced are not 

supporting the weight of other saw 

components. If a particular component is 

under pressure when connections points 

are loosened, oil may spray out 

forcefully.

 

43

Содержание CORE CUT CC9074DC-36









































































Отзывы:

Нет отзывов