Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 26

Страница: 26 / 72

OPERATING

Operating
General Operating Precautions

•

Prior to operating the machine, read the

operator’s manual thoroughly and ensure

that you understand the safe and proper

operation of the machine.

•

Use approved personal protective

equipment at all times while operating the

machine.

•

Ensure that there is firefighting equipment

and a first aid kit nearby while operating the

machine.

•

Ensure the cutting area is free of

obstructions, people, and or animals prior

to operating the machine.

•

Always operate the machine from the

operator’s position at the rear of the

machine between the handlebars.

•

Do not stand in front or behind the blade

path while the engine is running.

Emergency Stop

If an emergency condition should arise, the

machine is equipped with an emergency stop

button located on the top of the right side

switch box assembly. The emergency stop

places the machine into safe mode allowing

the operator to address the emergency

condition.

NOTE: Only use the emergency stop in an
emergency condition. Do not use it to stop the
machine during normal operations.

Activating the Emergency Stop

To activate the emergency stop, press down

on the emergency stop button. The engine will

shut off and the display panel will indicate that

the emergency stop is active.

Deactivating the Emergency Stop

Prior to deactivating the emergency stop,

ensure that the machine is back into a safe

operating condition. Then turn the emergency

stop button clockwise until it springs back into

position. The machine can now be restarted.

Emergency Stop

Handlebars

The handlebars help to guide and maneuver

the saw. During transporting of the saw, the

handlebars can be placed in the storage tubes

to save on space. When the handlebars are

removed for operation, ensure the handlebar

plug assembly is inserted into the storage tube

to minimize water and slurry buildup. Place the

handlebars in the desired position for better

leverage when lifting and steering. To

maneuver the saw forward or backward, turn

on the

Free Wheel

switch and move the saw

as desired.

NOTE: The free wheel component only works

with the ignition key at

ON position

Handlebar Storage

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 26 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: