manualshive.com logo in svg

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 25 / 72

Поделиться
Скачать
Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 25

 

DISPLAY PANEL 

Operation 

Turning the ignition key switch to 

ON

 will activate a sequence of screens on the display. First, the 

Diamond Products logo will appear followed by the “Blade Size Selection” screen. It is important to 

have the correct blade size selected for the installed drive configuration on the machine. Not having 

the proper blade size selected for the installed drive configuration will result in reduced cutting 

efficiency or serious bodily injury. Refer to the RPM and Blade Size Conversion Charts located in 

Appendix B at the end of this manual. 

 

To select the proper blade size scroll through the available blade sizes using the arrow keys  
(

)

 

on the right side of the display. Once the proper size is selected press the Select button

  

(

) on the left side of the display, this will save the blade size and open up the Home screen.  If the 

proper size is already showing on the screen, press the Deselect button (

) to toggle to the Home 

screen. 

Home Screen 

Once the blade size has been selected, the “Home Screen” will be displayed. There are three 

dynamic gauges that can be toggled through. 

Blade Speed 

This gauge shows the actual blade shaft speed that is being output by the shaft tach gear assembly.  

The blade speed limit is based on the blade size selected by the operator and is programmed into the 

controller to prevent an over-speed condition with the blade.  If the blade speed indication is lost, the 

blade shaft speed limit will be based on the factory set engine speed for the blade size setup originally 

ordered.  

Engine Torque 

This gauge will display the engine torque, in either foot pounds or newton meters (ft-lb or Nm) 

depending upon the units selected by the operator.  

Engine Speed 

This gauge will display the engine speed in RPM as output from the engine control unit (ECU). This 

speed is limited to the original factory setting based on the initial blade size ordered. 

  

 

 

25

Содержание CORE CUT CC9074DC-36









































































Отзывы:

Нет отзывов