Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 30

Страница: 30 / 72

OPERATING

The blade guard shields the blade and must

always be in place when operating the saw.

Blade guards generally stay in place at all

times, except for when changing to another

guard size or when using the guard on the

opposite side of the saw. Regularly inspect the

blade guard, the guard post assembly and

water tubes. Clean, repair, or replace dirty or

damaged components immediately.

NOTE: Always use a guard size that matches
the blade size. Refer to Appendix B.

Installing the Blade Guard

Always install the blade guard with the blade

off the saw.
1. Holding the blade guard handle, face the

front of the blade guard forward and fit the

tapered mount on the side of the guard

onto the tapered mount on the frame.

Frame Base Tapered Mount

2. Insert the lock pin through the hole on the

tapered frame mount to secure the guard.

3. For guards 36” and larger, place a lock

washer and then a flat washer onto the

blade guard screw. Fit the screw through

the slot near the back of the guard and

through the hole on the frame base, and

secure the guard to the frame using the

provided wrench.

4. Connect the water supply hose to the blade

guard.

NOTE: For 42” and larger blade guards there
is a guard post assembly that can be used to
stabilize the guard during operation. The
following steps outline the connection process:

1. Attach one end of the quick disconnect rod

to the guard post using the spring activated

ball joint quick disconnect and the ball stud

located on the guard post.

2. Attach the other spring activated ball joint

quick disconnect to the ball stud on the

blade guard.

Guard Post Assembly

Removing the Blade Guard

Always remove the blade guard with the blade

off the saw.

WARNING

When removing a guard 48” or larger, use a

hoist to avoid serious injury.

1. Disconnect the water supply hose from the

blade guard.

2. Remove the rear bolt from the blade guard

and frame base.

3. Remove the lock pin from the tapered

frame mount.

4. If the guard post is attached, disconnect it

from the blade guard.

5. Use the handle on the blade guard to rock

the guard back and forth while lifting the

guard off the tapered frame mount.

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 30 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: