Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 55

Страница: 55 / 72

MAINTENANCE

Blade Drive Belt Tensioning Bolt and Jam Nut

5. Turn both blade drive tension bolts equally

to tighten the belts. Test the belt tension

and readjust the bolts as necessary. DO

NOT exceed the manufacturer’s tension

settings.

6. Tighten the jam nut on both blade drive belt

tension bolts down to the jackshaft mounts.

7. Retighten the four pillow block bearing

mounting bolts.

Engine

WARNING

Let the engine cool down prior to

servicing the saw.

DO NOT service the saw with the

engine running (unless stated otherwise).

Refer to the engine manual and
manufacturer for a full engine maintenance
schedule and additional engine
maintenance information

Engine Control Unit (ECU)

The engine is equipped with an engine control

unit (ECU). The ECU monitors various engine

parameters to ensure optimal engine

performance and efficiency.

Warning

Never weld on the machine with the ECU

connected to the wire harness.

Battery

WARNING

Ignitable explosive gases are emitted from

the battery. DO NOT expose

the battery to sparks or open

flames, and keep the area

around the battery well-

ventilated.

Disconnect the battery prior to servicing the

saw (unless stated otherwise).

Always keep the battery cable clamps

away from the battery terminals

when the battery is disconnected

to avoid accidental connections

while servicing.

Always be sure to connect the battery cables

to the proper terminal when

reconnecting

CAUTION

Use a proper battery tester when testing the

battery strength.

Use protective eyewear or a face shield and

avoid contact with the skin when

handling/servicing the battery.

The saw contains a charged battery with one

positive cable lead and one negative cable

lead.

Battery – CC9074DKV

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 55 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: