Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 29

Страница: 29 / 72

OPERATING

Bogie Wheel – Locked Sideways Position

Bogie Wheel - Free Wheel Motion

To unlock the bogie wheel and allow it to move

freely:
1. Fully pull the ring on the detent pin.

2. Rotate the pin until the ring is horizontal to

the ground.

3. Release the pin in the locked open slot of

the pin assembly.

Bogie Wheel – Locked in Free Motion Position

WARNING

Keep feet clear. When the saw is raised on

any inclined surface, the bogie wheel must

be locked in a perpendicular position

(3 or 9 o’clock) to the rear wheels to prevent

the saw from rolling towards or away from

the operator.

Fuel System

WARNING

Always use caution when refueling.

DO NOT operate the saw with a fuel leak.

DO NOT fuel the saw with the

engine running.

DO NOT smoke or expose fuel to

open flames when filling the fuel

tank or working with fuel.

CAUTION

Clean up any spilled fuel prior to starting the

engine.

Fuel may seep out from the fuel cap vent

(applicable models) when raising the

saw if the fuel tank is overfilled.

Adding Fuel

1. Lower the saw to level the frame.

2. Turn off the engine and let the saw cool

down.

3. Remove the fuel tank cap.

4. Fill the fuel tank with ultra-low sulfur diesel

fuel only. DO NOT overfill the tank for

expansion purposes. Refer to the engine

manual for additional information.

5. Replace the fuel tank cap and secure.

Blade Guard

WARNING

DO NOT operate the saw with the blade

guard raised or removed.

DO NOT remove the blade guard with the

engine running.

Blade exposure should not exceed 180°

while cutting.

Always pivot the front of the blade

guard 180° (fully upward) so the

guard does not swing down

unexpectedly, which may cause serious

injuries.

Always secure the pivoted section of the

blade guard using the detent pin (guards

26” and up).

When pivoting the front of the blade guard,

raise/lower it cautiously and slowly to

avoid serious injuries.

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 29 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: