Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 57

Страница: 57 / 72

MAINTENANCE

Front Speed Cable Adjustment

Rear Speed Cable Adjustment

Adjusting the Lever Tension

Adjust the tension felt in the speed control

lever, when moving the lever forward and

backward, to the desired setting as necessary.
1. Open the rear cover screen.

2. Remove the grease cap from the pivot

housing.

3. Loosen the jam nut on the opposite side of

the speed control frame using the provided

wrench.

Grease Cap and Jam Nut

4. Use the hex wrench, located inside the

upright on the right hand side panel, to

adjust the shoulder screw.

5. Retighten the jam nut.

6. Move the speed control lever forward and

backward to test the lever tension.

Readjust the shoulder screw/jam nut if

desired.

7. Secure the grease cap to the pivot housing.

8. Close the rear cover screen and latch.

Adjusting the Spring Plungers

Adjust the spring plungers if the speed control

lever feels floppy or loose when moving the

lever forward and backward, or when the lever

is hard to place into or out of the

STOP/PARK

position.

1. Loosen both hex nuts from the speed

control tube.

Spring Plunger Hex Nuts

2. Screw the spring plungers slightly out to let

the speed control lever move easily into

and out of the

STOP/PARK

position. Screw

the spring plungers in slightly, to let the

speed control lever move forward and

backward firmly in the forward/reverse slot.

3. Retighten both hex nuts to secure.

Inner Blade Flange

Inner Flange

Содержание CORE CUT CC9074DC-36









































































Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы:

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 57 / 72

Результаты поиска

Содержание CORE CUT CC9074DC-36

Отзывы: