manualshive.com logo in svg

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 27 / 72

Поделиться
Скачать
Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 27

 

OPERATING 

 

Handlebar Plug Assembly 

 

Handlebar, Operating Position 

Adjusting the Handlebars 

1.  Loosen the handlebar adjusting lever. 

2.  Move the handlebar forward or backward to 

adjust the length and retighten the 

adjusting lever to secure.  

NOTE: Maintain a minimum of 6” of handlebar 
into the handlebar tube at all times.

 

3.  Press the 

Tilt Handlebar

 pushbutton, 

located on the side of the control grip, and 

move the handlebar up or down to adjust 

the angle.  

NOTE: The button only works with the ignition 
key at the ON position.

 

4.  To reposition adjustment lever, pull out and 

move to desired lever position. 

Speed Control Lever 

The speed control lever is a part of an electro-

mechanical assembly that allows the operator 

to raise and lower the machine, adjust the tilt of 

the handlebars, move the machine in a forward 

or reverse direction, or place the machine in 

STOP/PARK.

 

Control Grip Pushbuttons 

The control grip pushbuttons only work with the 

ignition key at 

ON

 or with the engine running. 

Control Grip Pushbuttons 

1.  Press the 

Raise

 (left) pushbutton to raise 

the saw and blade, and release to stop. 

NOTE: Always raise the blade when 
maneuvering the saw to provide proper 
clearance between the blade and the ground.

 

2.  Press the 

Lower

 (right) pushbutton to lower 

the saw and blade, and release to stop. 

3.  Press the 

Tilt Handlebar

 (side) pushbutton 

and move the handlebar up or down to 

adjust the angle

. 

 

 

27

Содержание CORE CUT CC9074DC-36









































































Отзывы:

Нет отзывов