manualshive.com logo in svg

Diamond Products CORE CUT CC9074DC-36, Руководство оператора, Страница: 39 / 72

Поделиться
Скачать
Diamond Products CORE CUT CC9074DC-36 Скачать руководство пользователя страница 39

 

OPERATING 

Drive Alignment 

Adjusting the Drive Alignment 

Adjust the rear axle when the saw’s drive 

alignment is off (saw will not cut in a straight 

line).  
1.  Turn the tap bolt clockwise using the 

provided wrench to adjust the drive 

alignment toward the right, or 

counterclockwise to adjust the drive 

alignment toward the left. 

Adjustment Bolt 

Footrest 

Use the footrest, if desired, to add body weight 

to the rear of the saw and improve the rear 

wheel traction when cutting. 

Footrest 

Weight Kit (Optional) 

The weight kit (optional) adds 200 Lbs. to the 

saw to improve the rear wheel traction when 

cutting. (Refer to the CC9074DKV Deep Cut 

Parts List manual) 

NOTE: The weight kit is a standard feature on 
the 54” and 60” blade saw

. 

Spotlight 

1.  Loosen both spotlight bar lock knobs and 

slide the spotlight bar from side-to-side to 

adjust the length of the bar. 

2.  Tighten the lock knobs to secure. 

3.  Turn the spotlight switch on or off as 

needed for additional lighting. 

 

Spotlight 

LED Light Bar 

1.  Loosen both light bar bolts and adjust the 

light angle from 0° to 30° in the downward 

direction.

 

2.  Tighten the bolts to secure.

 

3.  Turn the light bar switch on or off as 

needed for additional area lighting.

 

Light Bar 

Tie-Downs 

Use the tie-downs (two at the back and one at 

the front end of the saw) when securing the 

saw in a truck/trailer for transportation. DO 

NOT over-tighten a chain/rope to the front end 

tie-down, which may bend the frame and 

damage the saw 

 

39

Содержание CORE CUT CC9074DC-36









































































Отзывы:

Нет отзывов