Denon DCM280 - CD Changer Player, Руководство по эксплуатации

Страница: 15 / 82

15
ENGLISH
• The Time indicator indicates the amount of
elapsed time for the track currently being
played, the amount of time remaining for the
current track and the amount of time remaining
for all tracks yet to be played.
Normally, the amount of elapsed time for the
current track is displayed. Pressing this button
once causes the “EACH” “REMAIN” indicator
to light up, displaying the amount of time
remaining for the current track. Pressing the
button once more, causes the “TOTAL”
“REMAIN” and “–” indicator to light up,
displaying the number and the time remaining
for all tracks yet to be played on the disc.
Pressing the button once again turns the
“TOTAL” “REMAIN” indicator off and causes
the indicator to display the elapsed time for the
current track.
• During playback, the total remaining time is the
remaining time for the disc. For programmed
playback, the remaining time for the program is
only displayed when the programmed tracks are
all on the same disc.
“– – – –” is displayed when tracks on more than
one disc are programmed.
• In the case that the total playing time of
programmed tracks becomes more than 99:59,
“– –: – –” is displayed.
REMOTE CONTROL UNIT RC-258
Setting to the Program Mode
• For program search, press the PROG/DIRECT
button then the number buttons (1 through 10
and +10).
• The remote control unit is normally set to the
direct mode.
Open/Close Button ( 5 OPEN/CLOSE)
Random Button (RANDOM)
Repeat Button (REPEAT)
Number Buttons (1 ~ 10)
Play Button (
1
PLAY)
Pause Button ( 3 PAUSE)
Stop Button ( 2 STOP)
Automatic Search Reverse Button (
8
)
Automatic Search Forward Button (
9
)
Time Button (TIME)
Program/Direct Button (PROG/DIRECT)
Disc Select Button (DISC SELECT)
Call Button (CALL)
+10 Button (+10)
Disc Skip + Button (DISC SKIP +)
Button ()
Disc Skip – Button (DISC SKIP –)
Volume – Button (VOLUME –)
Manual Search Forward Button ( 7 )
Manual Search Reverse Button (
6
)
Use this to adjust the output level
output of the VARIABLE.
The volume increases when the “+”
button is pressed, decreases when the
“–” button is pressed.
• Disc Selection
Use the DISC SELECT and number buttons to
select the number of the disc to be played.
“–” appears on the disc number section of the
display for 2 seconds when the DISC SELECT
button is pressed. Press the number button
corresponding to the number of the disc to be
played while “–” is displayed to select the disc
number.
Track numbers are selected if the number buttons
are pressed while “–” is not displayed on the disc
number section of the display.
• Direct Selection
Normally, direct search is possible simply by
pressing the desired number buttons.
• Program Selection (During playback, the track
which is currently playing is programmed as the
1st track.)
Press the PROG/DIRECT button, then press the
number buttons.
For example, to program tracks number 3, 11, and
5, press PROG/DIRECT
/
3
/
+10 and 1
/
5.
To cancel the program, press the PROG/DIRECT
button.
• Inputting the Track Numbers
For track numbers below 10, simply press the
corresponding button. For track numbers of 11 and
greater, press the +10 then the number buttons.
For example, for track number 22 press +10 twice
then 2.
• Volume
The volume control on the unit will operate when
the VOLUME buttons are pressed. The volume can
be checked by looking at the position of the control.
• Skipping Discs
The DISC SKIP +, – button will not function in the
random and program modes.
During disc sequential random playback, when the
DISC SKIP + button is pressed, the following disc is
played in random order.
• Volume
The output level of the VARIABLE output terminal
can be changed.
When the VOLUME button is pressed, “–” appears
in the TIME M (minutes) section of the display
window and the level appears in the S (seconds)
section. The volume can be changed between a
maximum of “00” and a minimum of “–12” in 12
steps, by approximately 1.5 dB per step.