The default is listed in the previous table.
• Change the port priority of an interface.
INTERFACE mode
spanning-tree rstp priority
priority-value
The range is from 0 to 15.
The default is
128
.
To view the current values for interface parameters, use the
show spanning-tree rstp
command from
EXEC privilege mode.
Enabling SNMP Traps for Root Elections
and Topology Changes
To enable SNMP traps collectively, use this command.
Enable SNMP traps for RSTP, MSTP, and PVST+ collectively.
snmp-server enable traps xstp
Influencing RSTP Root Selection
RSTP determines the root bridge, but you can assign one bridge a lower priority to increase the likelihood that
it is selected as the root bridge.
To change the bridge priority, use the following command.
• Assign a number as the bridge priority or designate it as the primary or secondary root.
PROTOCOL SPANNING TREE RSTP mode
bridge-priority
priority-value
•
priority-value
The range is from 0 to 65535. The lower the number assigned, the more likely this
bridge becomes the root bridge.
The default is
32768
. Entries must be multiples of 4096.
Example of the bridge-priority Command
A console message appears when a new root bridge has been assigned. The following example example
shows the console message after the
bridge-priority
command is used to make R2 the root bridge
(shown in bold).
Dell(conf-rstp)#bridge-priority 4096
04:27:59: %RPM0-P:RP2 %SPANMGR-5-STP_ROOT_CHANGE: RSTP root changed. My Bridge ID:
4096:0001.e80b.88bd
Old Root: 32768:0001.e801.cbb4 New Root: 4096:0001.e80b.88bd
Rapid Spanning Tree Protocol (RSTP)
899
Содержание S4048T
