router-id {
number
}
•
number
: the IPv4 address.
The format is A.B.C.D.
NOTE:
Enter the router-id for an OSPFv3 router as an IPv4 IP address.
• Disable OSPF.
CONFIGURATION mode
no ipv6 router ospf
process-id
}
• Reset the OSPFv3 process.
EXEC Privilege mode
clear ipv6 ospf process
Configuring Stub Areas
To configure IPv6 stub areas, use the following command.
• Configure the area as a stub area.
CONF-IPV6-ROUTER-OSPF mode
area
area-id
stub [no-summary]
•
no-summary
: use these keywords to prevent transmission in to the area of summary ASBR LSAs.
•
Area ID
: a number or IP address assigned when creating the area. You can represent the area ID as
a number from 0 to 65536 if you assign a dotted decimal format rather than an IP address.
Configuring Passive-Interface
To suppress the interface’s participation on an OSPFv3 interface, use the following command.
This command stops the router from sending updates on that interface.
• Specify whether some or all some of the interfaces are passive.
CONF-IPV6-ROUTER-OSPF mode
passive-interface {
interface-type
}
Interface
: identifies the specific interface that is passive.
• For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
then the slot/port[/
subport] information.
• For a 40-Gigabit Ethernet interface, enter the keyword
fortyGigE
then the slot/port information.
• For a port channel interface, enter the keywords
port-channel
then a number.
• For a VLAN interface, enter the keyword
vlan
then a number from 1 to 4094.
To enable both receiving and sending routing updates, use the
no passive-interface interface
command.
To indicate that hello packets are not transmitted on that interface, when you configure a passive interface,
the
show ipv6 ospf interface
command adds the words
passive interface
.
Open Shortest Path First (OSPFv2 and OSPFv3)
738
Содержание S4048T
