Configure the VLTi between VLT peer 1 and VLT peer 2.
1
You can configure the LACP/static LAG between the peer units (not shown).
2
Configure the peer-link port-channel in the VLT domains of each peer unit.
Dell-2(conf)#interface port-channel 1
Dell-2(conf-if-po-1)#channel-member TenGigabitEthernet 1/4-1/7
Dell-4(conf)#interface port-channel 1
Dell-4(conf-if-po-1)#channel-member TenGigabitEthernet 1/4-1/7
Configure the backup link between the VLT peer units.
1
Configure the peer 2 management ip/ interface ip for which connectivity is present in VLT peer 1.
2
Configure the peer 1 management ip/ interface ip for which connectivity is present in VLT peer 2.
Dell-2#show running-config vlt
!
vlt domain 5
peer-link port-channel 1
back-up destination 10.11.206.58
Dell-2# show interfaces managementethernet 1/1
Internet address is 10.11.206.43/16
Dell-4#show running-config vlt
!
vlt domain 5
peer-link port-channel 1
back-up destination 10.11.206.43
Dell-4#
Dell-4#show running-config interface managementethernet 1/1
ip address 10.11.206.58/16
no shutdown
Configure the VLT links between VLT peer 1 and VLT peer 2 to the Top of Rack unit. In the following example,
port Te 1/4 in VLT peer 1 is connected to Te 1/8 of ToR and port Te 1/18 in VLT peer 2 is connected to Te
1/30 of ToR.
1
Configure the static LAG/LACP between the ports connected from VLT peer 1 and VLT peer 2 to the Top
of Rack unit.
2
Configure the VLT peer link port channel id in VLT peer 1 and VLT peer 2.
3
In the Top of Rack unit, configure LACP in the physical ports (shown for VLT peer 1 only. Repeat steps for
VLT peer 2. The bold
vlt-peer-lag port-channel 2
indicates that port-channel 2 is the port-
channel id configured in VLT peer 2).
Dell-2#show running-config interface tengigabitethernet 1/4
!
interface TenGigabitEthernet 1/4
no ip address
!
port-channel-protocol LACP
port-channel 2 mode active
no shutdown
configuring VLT peer lag in VLT
Dell-2#show running-config interface port-channel 2
!
interface Port-channel 2
no ip address
switchport
vlt-peer-lag port-channel 2
Virtual Link Trunking (VLT)
1140
Содержание S4048T
