and are buffered in queue 7, though you intended for these packets to match positive against
cmap2
and be
buffered in queue 4.
In cases such as these, where class-maps with overlapping ACL rules are applied to different queues, use the
keyword
order
. Dell Networking OS writes to the CAM ACL rules with lower order numbers (order numbers
closer to 0) before rules with higher order numbers so that packets are matched as you intended.
• Specify the order in which you want to apply ACL rules using the keyword
order
.
order
The order can range from 0 to 254.
By default, all ACL rules have an order of
255
.
Displaying Configured Class Maps and Match Criteria
To display all class-maps or a specific class map, use the following command.
Dell Networking OS Behavior
: An explicit “deny any" rule in a Layer 3 ACL used in a (match any or match all)
class-map creates a "default to Queue 0" entry in the CAM, which causes unintended traffic classification. In
the following example, traffic is classified in two Queues, 1 and 2. Class-map ClassAF1 is “match any,” and
ClassAF2 is “match all”.
• Display all class-maps or a specific class map.
EXEC Privilege mode
show qos class-map
Examples of Traffic Classifications
The following example shows incorrect traffic classifications.
Dell#show running-config policy-map-input
!
policy-map-input PolicyMapIn
service-queue 1 class-map ClassAF1 qos-policy QosPolicyIn-1
service-queue 2 class-map ClassAF2 qos-policy QosPolicyIn-2
Dell#show running-config class-map
!
class-map match-any ClassAF1
match ip access-group AF1-FB1 set-ip-dscp 10
match ip access-group AF1-FB2 set-ip-dscp 12
match ip dscp 10 set-ip-dscp 14
match ipv6 dscp 20 set-ip-dscp 14
!
class-map match-all ClassAF2
match ip access-group AF2
match ip dscp 18
Dell#show running-config ACL
!
ip access-list extended AF1-FB1
seq 5 permit ip host 23.64.0.2 any
seq 10 deny ip any any
!
ip access-list extended AF1-FB2
seq 5 permit ip host 23.64.0.3 any
seq 10 deny ip any any
!
ip access-list extended AF2
Quality of Service (QoS)
841
Содержание S4048T
