Dell PowerConnect J-SRX100 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 158

Dell PowerConnect J-SRX100 Скачать руководство пользователя страница 66

Figure 15: Connecting the Services Gateway to Power Supply

g031032

NOTE:

The device must be connected to earth ground during normal

operation. The protective earthing terminal on the rear of the chassis is
provided to connect the device to ground.

CAUTION:

We recommend using a surge protector for the power connection.

NOTE:

Use the cable tie holder to secure the power cord on to the power

supply point.

NOTE:

We strongly recommend that you use only the 3-pin power cord

supplied with your services gateway. If you are using a 2-pin power cord, then
ensure that your device is adequately grounded using the grounding point
available on back panel of chassis.

Related

Documentation

Required Tools and Parts for Installing and Maintaining the J-SRX100 Services Gateway
on page 31

•

•

Grounding the J-SRX100 Services Gateway on page 53

•

Connecting and Organizing Interface Cables to the J-SRX100 Services Gateway on
page 52

•

J-SRX100 Services Gateway General Safety Guidelines and Warnings on page 101

Connecting and Organizing Interface Cables to the J-SRX100 Services Gateway

You can connect the interfaces installed in the services gateway to various network
media. Each type of interface on the services gateway uses a particular medium to

52

PowerConnect J-SRX100 Services Gateway Hardware Guide

«
...
64
65
66
67
68
...
»

Содержание PowerConnect J-SRX100































































































































































Отзывы:

Нет отзывов