DataCard ImageCard series Скачать руководство пользователя | Manualshive

Страница: 89 / 159

background image

Advanced Information

5-7

User’s Guide for the Magna™ Class Printer

Network printing

This section describes how you can print to a Magna Class printer
over a network using Microsoft File and Printer Sharing.

The Magna Class printer drivers provide support for local printer
sharing. When a printer is locally shared, the printer is attached to
one PC (host) on a network. Users at other PCs on the network
(clients) can print to the shared printer over the network. Up to 10
client PCs can share the printer at one time. Users at client PCs do
not have the same level of access to the printer driver as a user at the
local PC.

Two operating system configurations are supported:

•

Both the client and host PCs run Windows NT 4.0 Workstation
with service Pack 5 or 6 installed.

•

Both the client and host PCs run Windows 98 (Second Edition).

Requirements for local printer sharing

Before sharing a printer over the network, meet the following
requirements:

•

A network card is installed and working on each PC.

•

The same Windows operating system is installed and operating
on each PC.

If you are installing both a network card and a service pack or
Windows upgrade, install the network card first and then install
the service pack or upgrade. If you installed a service pack or
upgrade before installing a network card, you must install the
service pack or upgrade again.

•

The printer must be enabled for sharing. See Windows help for
information on enabling printer sharing.

•

The PC with the printer attached must remain on, and the
Windows operating system must be running. For Windows NT, a
user with Full Control permission to the printer must be logged on
at the host PC so that other users can print.

E

MagnaUserGuide.book Page 7 Friday, May 5, 2000 1:09 PM

«
...
87
88
89
90
91
...
»

Содержание ImageCard series
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCard series

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 40

iP90 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

iPF650 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 16

iP100 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 2

imageRUNNER ADVANCE C5560

Бренд: Canon Страницы: 67

imageRUNNER 3300

Бренд: Canon Страницы: 366

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 252

iPF710 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 2

Бренд: G3D Страницы: 4

Бренд: Xerox Страницы: 89

Бренд: QMS Страницы: 208

Бренд: Oki Страницы: 52

Бренд: MEFA Страницы: 2

Бренд: Tektron Страницы: 72

Бренд: Ricoh Страницы: 236

Бренд: Oce Страницы: 32

Бренд: Oki Страницы: 94

Бренд: Oki Страницы: 109

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды