DataCard ImageCard series Скачать руководство пользователя

Страница: 118 / 159

6-16

Troubleshooting

User’s Guide for the Magna™ Class Printer

When to obtain service

Perform the steps earlier in this chapter before obtaining service. Call
for service if:

•

A troubleshooting process instructs you to call service

•

A troubleshooting process does not produce the expected result

•

You experience a problem repeatedly

Packing the printer for shipping

When service requests that you return the printer to a service center
for repair, pack the printer for shipping. You might also need to pack
the printer to send it to another location.

Pack the printer

Turn off power to the printer.

Remove the power cord from the printer and power receptacle.
Remove the interface cable and any other cables attached to the
printer.

–

If you are shipping the printer to use at another location, pack
the power cord, interface cable, and any other cables in the
accessories box.

–

If you are shipping the printer for service, do not ship cables
with the printer unless asked to do so.

Remove all cards from the card cartridge, and card output
stacker, and printer. Do not ship cards unless asked to do so.

Secure the print ribbon cartridge. Leave the print ribbon cartridge
in place or apply packing tape. See

Figure 2-5

for the location of

the tape. Avoid applying tape to labels in the printer.

Make sure all other supply cartridges are secured in place.

Close the cover.

Use the original shipping carton, plastic bag, and foam shipping
supports.

MagnaUserGuide.book Page 16 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды