DataCard ImageCard series Скачать руководство пользователя | Manualshive

Страница: 140 / 159

background image

User’s Guide for the Magna™ Class Printer

C

C

PC settings

This appendix provides information about
the PC on which the Magna Class printer
driver is installed. It describes:

•

Configuring the ECP parallel port

•

Setting port values

•

Setting printer permissions (Windows NT only)

•

Configuring the optional smart card serial port

This appendix includes a section for settings that are handled the
same way in all operating systems and also includes sections for
each PC operating system supported by the printer driver.

PC settings for all operating systems

This section describes how to configure the ECP parallel port.

Configuring the ECP parallel port

For most PCs, the parallel port is configured as an ECP parallel port
in the PC's BIOS. See the information that accompanies your PC for
details about changing the BIOS settings. The following applies to
most PCs and to the Windows NT and Windows 98 operating
systems.

Configure the ECP parallel port

1

Close all open applications.

2

Reboot the PC.

3

Enter Setup and follow the instructions that display early in the
reboot sequence. The setup screen will appear.

4

In Setup, check to see that the Parallel Port Mode field is set to
ECP. If it is not, set it to ECP.

MagnaUserGuide.book Page 1 Friday, May 5, 2000 1:09 PM

«
...
138
139
140
141
142
...
»

Содержание ImageCard series
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCard series

da Vinci 2.0 Duo

Бренд: XYZ Printing Страницы: 7

da Vinci Jr.1.0

Бренд: XYZ Printing Страницы: 8

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 62

WorkCentre 4260S

Бренд: Xerox Страницы: 8

Бренд: Canon Страницы: 738

Бренд: Samsung Страницы: 143

imageRUNNER 6570

Бренд: Canon Страницы: 274

Бренд: Xerox Страницы: 14

Бренд: Xerox Страницы: 2

Бренд: Ricoh Страницы: 682

Бренд: Durst Страницы: 2

Бренд: Olivetti Страницы: 111

Ecosys FS-C5300DN

Бренд: Kyocera Страницы: 35

Бренд: Ricoh Страницы: 678

Бренд: Lexmark Страницы: 2

Бренд: GALLERY Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды