DataCard ImageCard series Скачать руководство пользователя

Страница: 39 / 159

2-20

Getting started

User’s Guide for the Magna™ Class Printer

12 Pick up the overlay cartridge and turn it over. Turn the overlay

take-up knob clockwise

to remove any slack in the supply

material.

The overlay cartridge is ready to be replaced in the printer.

♦

Replacing the overlay cartridge

When replacing the overlay cartridge, begin with the top cover open.

Replace the overlay cartridge

Make sure the supply tracker is raised and out of the way. See

Figure 2-17

Hold the loaded overlay cartridge next to the overlay station, with
the cartridge handle toward you.

Align the overlay cartridge so the spools in the cartridge are even
with the spindles in the station.

Figure 2-19: Replace the overlay cartridge

MagnaUserGuide.book Page 20 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды