DataCard ImageCard series Скачать руководство пользователя

Страница: 113 / 159

Troubleshooting

6-11

Obtain guidance from service before performing this task.

User’s Guide for the Magna™ Class Printer

Optional overlay station

This section describes problems originating in the optional overlay
module.

Table 6-3: Overlay quality problems

What you see

Possible causes

Solutions

Supply material sticks to
leading edge of the card.

Temperature is too high.

The overlay station needs
fine tuning.

Decrease temperature for
the overlay module. See

Chapter 5

Contact your service
representative.

Supply material pulls the
card from the track.

Supply is loaded
incorrectly.

Temperature is too high.

You have switched to a
different card stock.

The overlay station needs
adjustment.

Load supply correctly. See

Chapter 2

Decrease temperature for
the overlay module. See

Chapter 5

Change settings for the
overlay module. See

Chapter 5

Contact your service
representative.

Proximity cards do not
work after overlay is
applied.

Debower is not set for the
cards you are processing.

Set the debower to off. See

Chapter 2

Cards are bowed (curved)
too much.

Debower is not set for the
cards you are processing.

Temperature is too high
for the card stock.

Set the debower to on. See

Chapter 2

Decrease temperature for
the overlay module. See

Chapter 5

Overlay patch comes off
the card when it is flexed.

Temperature is too low.

Increase the temperature
for the overlay module. See

Chapter 5

MagnaUserGuide.book Page 11 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды