DataCard ImageCard series Скачать руководство пользователя | Manualshive

Страница: 44 / 159

background image

Getting started

2-25

User’s Guide for the Magna™ Class Printer

is shorter. The overlay module makes a series of beeps while it is
warming up.

5

Press the PC Power button to turn on the power to the PC. Turn
on power to any other equipment needed.

The PC can be powered on before the printer; however, you
should wait a few minutes for the PC to obtain information from
the printer. The PC power can also remain on if the printer is
powered off.

♦

Installing the printer driver

The Magna Class printer comes with a CD-ROM that contains the
printer drivers for the Windows NT 4.0 and Windows 98 operating
systems. Use the following steps to install the printer driver on a PC
running one of the following operating systems:

•

Windows 98 (Second Edition recommended)

The printer driver for Windows 98 can be installed on a PC

with the Windows 95 operating system; however, unexpected
results might occur. If you use Windows 95, follow
procedures in this guide and in help for Windows 98.

•

Windows NT 4.0, with Service Pack 5 or 6. The Magna Class
printer driver is not supported for PCs with Alpha, MIPS, or
PowerPC processors.

If the PC does not have a CD-ROM drive, request installation

diskettes from your service provider. You also can download the
printer driver from the Datacard Web site, at www.datacard.com.

If you have installed the printer driver and want to update to the

most recent driver, delete the existing printer driver following the
steps in

“Reinstalling the printer driver” on page 5-1

. Then, use

the following steps to install the new printer driver.

i

E

E

i

E

E

MagnaUserGuide.book Page 25 Friday, May 5, 2000 1:09 PM

«
...
42
43
44
45
46
...
»

Содержание ImageCard series
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCard series

Бренд: Felix Storch Страницы: 39

Бренд: Felix Storch Страницы: 10

Бренд: Xerox Страницы: 8

Бренд: Oce Страницы: 136

Бренд: Oce Страницы: 116

Бренд: Konica Minolta Страницы: 20

Бренд: Oki Страницы: 40

WorkCentre Pro 90

Бренд: Xerox Страницы: 36

16C0365 - 5500 MFP

Бренд: Lexmark Страницы: 88

Бренд: SPRT Страницы: 15

Бренд: Oki Страницы: 220

Бренд: Canon Страницы: 50

imagePRESS V1000

Бренд: Canon Страницы: 123

Бренд: Lexmark Страницы: 2

M-Class Mark II M-4206

Бренд: Datamax Страницы: 76

Бренд: Epson Страницы: 7

LabelWorks Safety Kit

Бренд: Epson Страницы: 42

LASER PRINTER C3900DN

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды