DataCard ImageCard series Скачать руководство пользователя | Manualshive

Страница: 13 / 159

background image

Overview

1-5

User’s Guide for the Magna™ Class Printer

The ML and M2L models of the printer include the overlay
module which applies a durable polyester patch (overlay) to one
or both sides of the personalized card. You can select the type
and thickness of the overlay to use.

Printer features

Use the information in this section to identify the features and controls
you use on the printer.

Figure 1-4: Front of the Magna Class printer

Front of the printer

Find the following on the outside of the printer:

Card cartridge

The card cartridge holds blank cards to print. It holds about 100 cards
(with a nominal thickness of 0.030 inches (0.76 mm)). At the bottom
of the card cartridge, the exception card slot allows you to insert a
single card that is different from the cards in the card cartridge.

Duplex module

Swing arm

Cover

Card cartridge

Exception card slot

Overlay module

Overlay supply
cartridge

Overlay card
feed knob

Print ribbon cartridge

Printhead cartridge

Manual card
feed knob

Ready button

Status light

Card output
stacker

Top cover support

MagnaUserGuide.book Page 5 Friday, May 5, 2000 1:09 PM

«
...
11
12
13
14
15
...
»

Содержание ImageCard series
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCard series

Бренд: Felix Storch Страницы: 39

Бренд: Felix Storch Страницы: 10

Бренд: Raymarine Страницы: 135

Бренд: Oki Страницы: 28

Бренд: Inno3D Страницы: 23

Бренд: B9Creator Страницы: 27

Бренд: Fenix Страницы: 57

Aficio SP 320 Series

Бренд: Ricoh Страницы: 272

Бренд: TRENDnet Страницы: 135

Бренд: Ricoh Страницы: 23

Бренд: Xiamen Sojet Electronics Страницы: 37

Бренд: Felix Storch Страницы: 35

Бренд: Epson Страницы: 61

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 5

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды