DataCard ImageCard series Скачать руководство пользователя

Страница: 79 / 159

4-10

Maintaining the printer

User’s Guide for the Magna™ Class Printer

Use the cleaning stick to move the heated roller
counterclockwise and make another area available for
cleaning (step 2 in

Figure 4-9

If the heated roller does not move, clean the visible area and
continue with step 5.

Repeat steps a and b to clean the entire area of the heated
roller.

Figure 4-9: Clean the heated roller

Replace the overlay cartridge. See

“Replacing the overlay

cartridge” on page 2-20

Close the cover by lifting the top slightly. Move the cover support
up so it is parallel with the hinges. Close the cover of the printer.

Power on the printer to resume card production.

Repeat if needed.

♦

MagnaUserGuide.book Page 10 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды