DataCard ImageCard series Скачать руководство пользователя

Страница: 77 / 159

4-8

Maintaining the printer

User’s Guide for the Magna™ Class Printer

Clean the supply tracker

Power off the printer.

Prepare a printer cleaning card.

–

If you just used a printer cleaning card in the printer, you can
use that card to complete this procedure.

–

If you have not run a printer cleaning card, remove the
protective paper from one side of the card.

Figure 4-7: Remove the protective paper from the cleaning card

Lift the supply tracker until it stops and holds it in place.

Remove the overlay cartridge for easier access to the supply

tracker. See

“Removing the overlay cartridge” on page 2-17

for steps to follow.

Roll the sticky surface of the cleaning card against the overlay
supply tracker. Rotate the supply tracker to clean all sides.

Do not touch the surface of the supply tracker with your fingers.
Oils from the skin can cause the supply tracker to slip or can
affect card quality.

Figure 4-8: Clean the supply tracker

MagnaUserGuide.book Page 8 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды