DataCard ImageCard series Скачать руководство пользователя

Страница: 50 / 159

Getting started

2-31

User’s Guide for the Magna™ Class Printer

Printer test card

The printer test card is designed to perform most of the functions
available in the printer.

Figure 2-24: Printer test card

Check the following:

•

The test card has the pattern shown on the front of the card. The
back of the card is unprinted.

•

If a topcoat (T) panel is included in the ribbon and you select a
ribbon type that applies topcoat to the front of the card, the front
of the card has topcoat applied.

•

If a magnetic stripe module is installed in the printer and enabled,
the following data is encoded on the card:

See

“Magnetic stripe encoding” on page D-1

for more information

about magnetic stripe tracks.

icivtc

Track Format

Data

Track 1

(IATA)

TEST PATTERN IATA CHARACTER
SUBSET 0123456789

Track 2

(ABA)

012345678012345678990123456789

Track 3

(NTT)

0123456789=9876543210

Track 3

(TTS)

0123456789=9876543210

MagnaUserGuide.book Page 31 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды