DataCard ImageCard series Скачать руководство пользователя

Страница: 24 / 159

Getting started

2-5

User’s Guide for the Magna™ Class Printer

If you store the Magna Class printer, provide an environment with the
following conditions:

•

Storage relative humidity: 20% to 80% non-condensing

•

Storage temperature range: 0° F to 100° F (-17.8° C to 37.8° C)

Unpacking the printer

Follow these steps to unpack the printer. Be sure to select a location
that meets the site requriements for the Magna Class printer. See

“Selecting the site” on page 2-2

for more information.

You need scissors or another cutting device to unpack the printer.

Make sure you have one or more people to assist with unpacking the

printer. One or two people can lift the printer while another person
assists with removing packaging.

Unpack the printer

Place the shipping carton on a firm level surface.

Use a scissors to open the taped area on top of the shipping
carton.

Open the shipping carton (step 1 in

Figure 2-3

MagnaUserGuide.book Page 5 Friday, May 5, 2000 1:09 PM

Содержание ImageCard series
































































































































































Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды

DataCard ImageCard series, Руководство пользователя

Результаты поиска

Содержание ImageCard series

Отзывы:

Похожие инструкции для ImageCard series

Бренды по названию

Популярные бренды