MB-240X Wheel Balancer
37
P/N 5900262 — Rev. A1 — Jan. 2021
ALU2
ALU2 Mode is used on Aluminum Alloy Wheels when the weights
are to be applied to the Inner Plane and the Center Plane.
Select the ALU 2 Mode by pressing the
F
key until the indicator
next to the ALU 2 is lit.
Pull out the Inner Arm and place it on the
Inner Edge
and hold it
there. Read the distance off the arm and enter this data into the Balancer using the
Distance
+
/
—
key
.
-A-
will appear in the Inner Display Window and the distance value will appear in the Outer
Display Window.
Measure the width of the Wheel using the Wheel caliper. Enter this width into the Balancer using
the
Width
+
/
—
keys.
-L-
will appear in the Inner Display Window and the value will appear in the
Outer Display Window.
Enter the Wheel diameter by reading the size off the Tire sidewall and enter this into the Balancer
using the
Diameter
+
/
—
keys.
-D-
will appear in the Inner Display Window and the diameter
value will appear in the Outer Display Window.
While facing the Wheel, start spinning the Wheel in a clockwise
direction. Begin by pushing with
your hand against the Tire, then turn the Quick Nut black handles to increase the speed of rotation
until the Outer Display Window reads
run
.
Release the handles and wait. The display will go blank then the imbalance value will appear in the
Inner and Outer display windows.
Pull the brake against the Tire to stop the Tire rotation.
⚠
WARNING
Do
not
attempt to stop a rotating Wheel with your hands. Always use the brake.
Even though there is no motor driving the Wheel it can severely injure you if it is in
motion.
When the Wheel stops, look at the values that appear in the Inner and Outer Windows on the
Display Panel; this is the unbalanced correction weight required for each plane measured in grams.
The value that appears in the Inner Window should be added to the
Inner Plane
of the Wheel.
The value that appears in the Outer Window should be added to the
Center Plane
of the Wheel.
Turn the Wheel slowly to find the best location to put the weight on the
Inner Plane
. The Inner
Edge/Plane placement indicators located under the Inner Display Window light up or go out as you
move the Wheel to find the best location to put the weight. When all the indicators on the Inner
plane are lit engage the brake to hold the Wheel and apply the correct value weight to the inner
plane of the Wheel at the 12 o’clock position. (If the Inner Display Window shows
00
, do not add
any weight to the Inner Plane).
Turn the Wheel slowly again to find the best location for the weight on the
Center Plane
. The
Outer Edge/Plane placement indicators located under the Outer Display Window light up or go out
as you move the Wheel to find the best location to put the weight. When all the indicators on the
Outer Edge/Plane are lit, engage the brake to hold the Wheel and apply the correct value weight to
Содержание MB-240X
