![background image](http://html1.mh-extra.com/html/dannmar/mb-240x/mb-240x_installation-and-operation-manual_3431293018.webp)
MB-240X Wheel Balancer
18
P/N 5900262 — Rev. A1 — Jan. 2021
Installing the MB-240X Balancer on the Wall Bracket
The MB-240X Wall Brackets are an optional mounting configuration. This configuration allows the
Balancer to be mounted on a wall, consuming a minimum of floor space.
To install the MB-240X on the Wall Bracket:
Refer to
Figure C
on the following page.
The location should be away from pedestrian traffic.
The location
must be no less than 22 in. / 560 mm off the ground
and allow for easy
movement of Wheels and Tires around the Balancer without causing a hazard to personnel.
⚠
DANGER
Consult a qualified, licensed contractor to wall mount the MB-240X. Only wall
mount the MB-240X on a core-filled masonry block, or a reinforced concrete wall.
The wall must be capable of supporting the weight of the MB-240X, the Wheel and
the Tire. This combined weight can exceed 225 lbs. / 102 kg. Anchors in drywall
will not support this Balancer and Wheel. Serious injury can result from the Balancer
tearing away from a drywall mount.
Tip
The Wall and mounting must be rigid enough to prevent the Balancer from moving during
balancing. Inaccurate readings can result from a Balancer that moves during test.
Assemble the Wall Brackets (2)(3)(4)(5)(6).
Dannmar strongly recommends having a second person help install the Balancer on the wall
mount bracket.
Locate the Bracket on a wall rated to accept
>225 lbs. / 102 kg.
Have a second person hold the assembled wall mount brackets against the wall and use a level to
adjust and verify the brackets are level. Mark the anchor hole locations on the wall.
Remove the brackets and drill four holes on the marks. If this is a reinforced concrete or core-filled
block wall, use an appropriate masonry drill bit. Use a 10 mm drill for a 10 mm anchor. Refer to
for additional information.
Clean the debris from the drill hole using a vacuum and brush.
Install the Anchors (12) in the Wall Mount Brackets with Washers and Nuts (7)(8).
Place the Anchors with the bracket on the wall and hammer or mallet the Anchors in to the drilled
holes.
Tighten the Nuts finger tight.
Using a small level to verify the brackets are level, you may lightly tap the bracket to correct any out
of level condition. You may have to loosen the Nuts slightly. Once the bracket is straight and level
re-tighten the Nuts on the Anchors.
Important
Dannmar strongly recommends having a second person help install the Balancer on
the bracket.
Attach the Balancer (1) on the wall mounting brackets using M10 Screws (11).
Attach the Cone Tooling Bracket (9) on the front right side of the assembly, using the Screws
supplied.
Содержание MB-240X
