Manual.
MB-240X Wheel Balancer, Installation and Operation Manual, P/N 5900262, Manual Revision A1,
released January 2021.
Copyright.
Copyright © 2021 by Inc. All rights reserved. You may make copies of this document if you agree
that: you will give full attribution to BendPak Dannmar Inc., you will not make changes to the content, you do not
gain any rights to this content, and you will not use the copies for commercial purposes.
Trademarks.
BendPak, the BendPak logo, Dannmar, and the Dannmar logo are registered trademarks of
BendPak Inc. All other company, product, and service names are used for identification only. All trademarks and
registered trademarks mentioned in this manual are the property of their respective owners.
Limitations.
Every effort has been made to have complete and accurate instructions in this manual. However,
product updates, revisions, and/or changes may have occurred since this manual was published. BendPak
Dannmar reserves the right to change any information in this manual without incurring any obligation for
equipment previously or subsequently sold. BendPak Dannmar is not responsible for typographical errors in this
manual. Feel free to contact us at any time to get the latest information about any product:
Warranty.
The BendPak Dannmar warranty is more than a commitment to you: it is also a commitment to the
value of your new product. For full warranty details, contact your nearest BendPak Dannmar dealer or visit
.
Go to
and fill out the online form to register your
product (be sure to click
Submit
).
Safety.
Your new product was designed and manufactured with safety in mind. Your safety also depends on
proper training and thoughtful operation. Do not set up, operate, maintain, or repair the unit without reading and
understanding this manual and the labels on it;
do not use this product unless you can do so safely!
Owner Responsibility.
In order to maintain your product properly and to ensure operator safety, it is the
responsibility of the product owner
to read and follow these instructions
:
• Follow all setup, operation, and maintenance instructions.
• Make sure product setup conforms to all applicable local, state, and federal codes, rules, and regulations,
such as state and federal OSHA regulations and electrical codes.
• Read and follow all safety instructions. Keep them readily available for operators.
• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.
• Do not operate the product until you are certain that all parts are in place and operating correctly.
• Carefully inspect the product on a regular basis and perform all maintenance as required.
• Service and maintain the unit only with approved replacement parts.
• Keep the manual with the product and make sure all labels are clean and visible.
•
Only use this product if it can be used safely!
Unit Information.
Enter the Model Number, Serial
Number, and the Date of Manufacture from the label
on your unit. This information is required for part or
warranty issues.
Model:
Serial:
Date of Manufacture:
Содержание MB-240X
