![background image](http://html1.mh-extra.com/html/dannmar/mb-240x/mb-240x_installation-and-operation-manual_3431293013.webp)
MB-240X Wheel Balancer
13
P/N 5900262 — Rev. A1 — Jan. 2021
Unpacking
Use caution when unpacking the Balancer from its shipping container. You do not want to damage the
unit, misplace any of the components that come with it, or hurt anyone.
⚠
CAUTION
Make sure to use an appropriate lifting device, such as a Forklift or pallet jack, to
move the Balancer while it is on its pallet. Make sure only personnel who are
experienced with material handling procedures are allowed to move the Balancer.
The Balancer is heavy and the weight is not evenly distributed; dropping or
knocking over the unit may cause equipment damage or personal injury. Do not lift
the Balancer by the Shaft or its housing; it will damage the Balancer.
We recommend you unpack the Balancer in the area where you are going to set it up.
To unpack the Balancer
:
Remove the carton by flipping down the metal tabs at the bottom and pulling off the top.
Remove the shipping bolts that are holding the Balancer to the Pallet.
Remove the straps and plastic wrap that held the Balancer components during shipping.
Move the Balancer off the Pallet, then move it to the desired location.
⚠
WARNING
Do not lift the Balancer by the Shaft; it is not strong enough to bear the weight of
the Balancer.
⚠
CAUTION
Dannmar recommends having at least two people move the Balancer; it is heavy. If
it is dropped or falls, it could cause injuries and/or the Balancer could be damaged.
Installing the MB-240X on the Mounting Stand
An
optional
Mounting Stand is available for the MB-240X. The MB-240X Mounting Stand comes
complete with all attaching hardware required to install the Balancer.
Refer to
Figure A
on the following page.
To install the Balancer on the Mounting Stand:
Remove the Recessed Cross Screws (3) from the Mounting Stand (5) and open the Cover (4).
Install the cone holders on the back side of the Mounting Stand.
Place the Balancer (1) on top of the Stand (5) and use four M10 Screws (2) to fasten the Balancer
to the Mounting Stand.
Replace the Cover (4) and tighten the fasteners (3).
Move the Balancer to the desired location and match drill the holes for the Mounting Anchors.
Vacuum and brush the debris from the holes, then install the Anchors. Refer to
Tighten the Anchors to prevent the Balancer from moving. The mounting must be rigid to prevent
the Balancer from moving during the balancing operation. Inaccurate test results can be caused by
a Balancer that moves during test.
Содержание MB-240X
