manualshive.com logo in svg

Cypress CY8C28 series, Техническое справочное руководство

Cypress CY8C28 серии - продукт с высокой технической мощностью. Пользователи могут бесплатно скачать техническое руководство для подробной информации по настройке и использованию. Доступен для загрузки с официального веб-сайта.

Поделиться
Скачать
background image

352

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

Digital Blocks

17.2.1.6

SPI Master Register Definitions 

There are three 8-bit Data registers and two Control/Status registers (an 8-bit and a 7-bit). 

Table 17-16

 explains the meaning

of these registers in the context of SPIM operation. The Control registers are described beginning with section 

17.2.2

DxCxxCR0 Register

. 

17.2.1.7

SPI Slave Register Definitions 

There are three 8-bit Data registers and two Control/Status registers (an 8-bit and a 7-bit). 

Table 17-17

 explains the meaning

of these registers in the context of SPIS operation. The Control registers are described beginning with section 

17.2.2

DxCxxCR0 Register

. 

17.2.1.8

Transmitter Register Definitions 

There are three 8-bit Data registers and one 5-bit Control/Status register. 

Table 17-18

 explains the meaning of these registers

in the context of Transmitter operation. The Control registers are described beginning with section 

17.2.2 DxCxxCR0 Regis-

ter

.

Table 17-16.  SPIM Data Register Descriptions

Name

Function

Description

DR0

Shifter

Not readable or writeable. 

During normal operation, DR0 implements a Shift register for shifting serial data.

DR1

TX Buffer

Write only register. 

If no transmission is in progress and this register is written to, the data from this register (DR1) is loaded into the Shift regis-
ter (DR0), on the following clock edge, and a transmission is initiated.    If a transmission is currently in progress, this register 
serves as a buffer for TX data. 

This register should only be written to when TX Reg Empty status is set, and this write clears the TX Reg Empty status bit in 
the Control register. When the data is transferred from this register (DR1) to the Shift register (DR0), then TX Reg Empty sta-
tus is set. 

DR2

RX Buffer

Read only register. 

When a byte transmission/reception is complete, the data in the shifter (DR0) is transferred into the RX Buffer register and 
RX Reg Full status in the Control register is set. 

A read from this register (DR2) clears the RX Reg Full status bit in the Control register.

Table 17-17.  SPIS Data Register Descriptions

Name

Function

Description

DR0

Shifter

Not readable or writeable. 

During normal operation, DR0 implements a Shift register for shifting serial data.

DR1

TX Buffer

Write only register. 

This register should only be written to when TX Reg Empty status is set and the write clears the TX Reg Empty status bit in 
the Control register. When the data is transferred from this register (DR1) to the Shift register (DR0), then TX Reg Empty sta-
tus is set.

DR2

RX Buffer

Read only register. 

When a byte transmission/reception is complete, the data in the shifter (DR0) is transferred into the RX Buffer register and 
RX Reg Full status in the Control (CR0) register is set. 

A read from this register (DR2) clears the RX Reg Full status bit in the Control register.

Table 17-18.  Transmitter Data Register Descriptions

Name

Function

Description

DR0

Shifter

Not readable or writeable. 

During normal operation, DR0 implements a shift register for shifting out serial data.

DR1

TX Buffer

Write only register. 

If no transmission is in progress and this register is written to, subject to the setup time requirement, the data from this regis-
ter (DR1) is loaded into the Shift register (DR0) on the following clock edge and a transmission is initiated.    If a transmission 
is currently in progress, this register serves as a buffer for TX data.

This register should only be written to when TX Reg Empty status is set and this write clears the TX Reg Empty status bit in 
the Control (CR0) register. When the data is transferred from this register (DR1) to the Shift register (DR0), then TX Reg 
Empty status is set. 

DR2

NA

Not used in this function.

Содержание CY8C28 series




























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CY8C28 series

Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Бренд: Baader Planetarium Страницы: 7
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Бренд: Taco Electronic Solutions Страницы: 28
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Бренд: fadini Страницы: 28
Eaton CDAU-01/04 Instruction Leaflet preview
CDAU-01/04
Бренд: Eaton Страницы: 4
tbs electronics Omnicharge Solar OCS 100-20 Installation Manual preview
Omnicharge Solar OCS 100-20
Бренд: tbs electronics Страницы: 64
Maximum Controls MAX ARM Installation And Owner'S Manual preview
MAX ARM
Бренд: Maximum Controls Страницы: 58
Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Бренд: Magicfx Страницы: 16
Ezodo 4801P Manual preview
4801P
Бренд: Ezodo Страницы: 7
AirCycler SmartExhaust Manual preview
SmartExhaust
Бренд: AirCycler Страницы: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Бренд: TS Performance Страницы: 4
Mold-Masters TempMaster M2 Plus Series Quick Manual preview
TempMaster M2 Plus Series
Бренд: Mold-Masters Страницы: 2
Trinamic TMCM-1240 Hardware Manual preview
TMCM-1240
Бренд: Trinamic Страницы: 30
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Бренд: HANYOUNG NUX Страницы: 4
Rheem RXMD-B04 Installation Instructions preview
RXMD-B04
Бренд: Rheem Страницы: 2
FASTRON. FTM1 Series User Manual preview
FTM1 Series
Бренд: FASTRON. Страницы: 37
Festo MPAL-VI Original Instructions preview
MPAL-VI
Бренд: Festo Страницы: 2
Sorel SBMC Installation And Operating Instructions Manual preview
SBMC
Бренд: Sorel Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды