manualshive.com logo in svg

Cypress CY8C28 series, Техническое справочное руководство

Cypress CY8C28 серии - продукт с высокой технической мощностью. Пользователи могут бесплатно скачать техническое руководство для подробной информации по настройке и использованию. Доступен для загрузки с официального веб-сайта.

Поделиться
Скачать
background image

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

453

Two Column Limited Analog System

Analog Interface Registers

24.3.2

DEC_CR0 Register

The Decimator Control Register 0 (DEC_CR0) contains con-
trol bits to access hardware support for both the Incremental
ADC and the DELISG ADC.

This register can only be used with four and two analog col-
umn PSoC devices.

Bits 7 to 4: ACC_IGEN[3:0].  

For incremental support,

these bits select which column comparator bit will be gated
by the output of a digital block. The output of that digital
block is typically a PWM signal; the high time of which corre-
sponds to the ADC conversion period. This ensures that the
comparator output is only processed for the precise conver-
sion time. The digital block selected for the gating function is
controlled by ICLKS0 in this register, and ICLKS3, ICLKS2
and ICLKS1 bits in the DEC_CR1 register.

Bit 3: ICLKS0.  

In conjunction with ICLKS1, ICLKS2, and

ICLKS3 in the DEC_CR1 register, these bits select up to
one of 16 digital blocks (depending on the PSoC device
resources) to provide the gating signal for an incremental
ADC conversion.

Bits 2 and 1: ACE_IGEN[1:0].  

For incremental support,

these bits select which type E column comparator bit will be
gated by the output of a digital block. The output of that digi-
tal block is typically a PWM signal, the high time of which
corresponds to the ADC conversion period. This ensures
that the comparator output is only processed for the precise
conversion time. The digital block selected for the gating
function is controlled by ICLKS[3:0]

Bit 0: DCLKS0.  

The decimator requires a timer signal to

sample the current decimator value to an output register that
may subsequently be read by the CPU. This timer period is
set to be a function of the DELSIG conversion time and may
be selected from up to one of twelve digital blocks (depend-
ing on the PSoC device resources) with DCLKS0 in this reg-
ister and DCLKS3, DCLKS2, and DCLKS1 in the DEC_CR1
register. If the Decimation Rate bits are set in DECx_CR this
setting is overwritten

For additional information, refer to the 

DEC_CR0 register on

page 212

.

24.3.3

DEC_CR1 Register

The Decimator Control Register 1 (DEC_CR1) is used to
configure the decimator prior to using it.

This register can only be used with four and two analog col-
umn PSoC devices.

Depending on how many analog columns your PSoC device
has (see the Cols. column in the register table above), only
certain bits are accessible to be read or written.

Bit 6: IDEC.  

Any function using the decimator requires a

digital block timer to sample the current decimator value.
Normally, the positive edge of this signal causes the decima-
tor output to be sampled. However, when the IDEC bit is set,
the negative edge of the selected digital block input causes
the decimator value to be sampled.

Bits 5 to 0: ICLKSx and DCLKSx.  

The ICLKS3, ICLKS2,

ICLKS1, DCLKS3, DCLKS2, and DCLKS1 bits in this regis-

ter select the digital block sources for Incremental and DEL-
SIG ADC hardware support (see the DEC_CR0 register). 

For additional information, refer to the 

DEC_CR1 register on

page 213

.

Add.

Name

Cols.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,E6h

DEC_CR0

4, 2

ACC_IGEN[3:0]

ICLKS[0]

ACE_IGEN[1:0]

DCLKS0

RW : 00

Address

Name

Cols.

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,E7h

DEC_CR1

4

IDEC

ICLKS3

ICLKS2

ICLKS1

DCLKS3

DCLKS2

DCLKS1

RW : 00

2

IDEC

ICLKS3

ICLKS2

ICLKS1

DCLKS3

DCLKS2

DCLKS1

RW : 00

Содержание CY8C28 series




























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CY8C28 series

Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Бренд: Objective Imaging Страницы: 11
Ubiquiti UA-Hub Quick Start Manual preview
UA-Hub
Бренд: Ubiquiti Страницы: 16
Danfoss ECL Comfort 300 User Manual preview
ECL Comfort 300
Бренд: Danfoss Страницы: 75
Parker Sporlan 952567 Installation And Operation Instructions Manual preview
Sporlan 952567
Бренд: Parker Страницы: 24
ETI PFC 12 RS User And Service Manual preview
PFC 12 RS
Бренд: ETI Страницы: 14
WAGO 750-8202/040-000 Manual preview
750-8202/040-000
Бренд: WAGO Страницы: 418
fadini Elpro S40 Manual preview
Elpro S40
Бренд: fadini Страницы: 40
AMX NX-2200 Quick Start Manual preview
NX-2200
Бренд: AMX Страницы: 2
Instruments of Things IO-Lights User Manual preview
IO-Lights
Бренд: Instruments of Things Страницы: 12
LAE electronic RDC123T1R3C Instructions For Installation And Use preview
RDC123T1R3C
Бренд: LAE electronic Страницы: 4
NEEDO MY NEEDO User Manual Book preview
MY NEEDO
Бренд: NEEDO Страницы: 193
Danfoss ADAP-KOOL AK-CC 750 Service Manual preview
ADAP-KOOL AK-CC 750
Бренд: Danfoss Страницы: 6
Berker 85865100 Operation Instructions preview
85865100
Бренд: Berker Страницы: 2
Vent-Axia Visionex Fitting & Wiring Instructions preview
Visionex
Бренд: Vent-Axia Страницы: 4
Canford TECPRO HS581 Manual preview
TECPRO HS581
Бренд: Canford Страницы: 2
Genave RXC-3000 Hardware Manual preview
RXC-3000
Бренд: Genave Страницы: 46
Infineon XC164CM Series Manual preview
XC164CM Series
Бренд: Infineon Страницы: 28
ST STM32MP157A-DK1 User Manual preview
STM32MP157A-DK1
Бренд: ST Страницы: 47

Бренды по названию

Популярные бренды

Загрузить еще бренды