Compaq AlphaServer DS20 Скачать руководство пользователя страница 70

Страница: 70 / 182

2-20

AlphaServer DS20 Service Manual

2.9

Releasing Secure Mode

The console cannot be secure for most SRM console commands to run. If the
console is not secure, user mode console commands can be entered. See the
system manager if the system is secure and you do not know the password.

Example 2–7 Releasing/Reestablishing Secure Mode

P00>>> login
Please enter password: xxxx
P00>>>

[User mode SRM console commands are now available.]

P00>>> set secure

The console command login clears secure.

If the password has been forgotten and the system is in secure mode, enter the login
command:

P00>>> login

please enter password:

At this prompt, press the Halt button and then press the Return key.

The password is now cleared and the console is in user mode. A new password must
be set to put the console into secure mode again.

For a full discussion of securing the console, see your system User’s Guide.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды

Compaq AlphaServer DS20, Руководство по обслуживанию

Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды