Compaq AlphaServer DS20 Скачать руководство пользователя страница 117

Страница: 117 / 182

Removal and Replacement

4-27

Removal

Shut down the operating system and turn the system off.

Unplug the AC power cord. (Auxiliary power is applied to the server feature
module and parts of the system board even when the system is turned off.)

Expose the card cage side of the system (see Section 4.3).

Removing Fan 0

Remove the CPU module(s).

Unplug the power cord to fan 0 from the server feature module.

Unscrew the fan from the frame and remove it from the system.

Removing Fan 1

Remove any PCI modules that prevent access to the four Phillips head screws that
hold fan 1 in place.

Remove any plastic module guides that prevent access to the Phillips head screws.

Unplug the power cord to fan 1 from the server feature module.

Unscrew the fan from the frame and remove it from the system.

Replacement

Reverse the steps in the Removal procedure.

Verification

Power up the system. If the fan is faulty, the system will run for approximately 30
seconds and then power down.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды

Compaq AlphaServer DS20, Руководство по обслуживанию

Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды