Compaq AlphaServer DS20 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 182

background image

Removal and Replacement

4-21

Removal

1.

Shut down the operating system and power down the system.

2.

Remove the AC power cords. (Auxiliary power is applied to the server feature
module and parts of the system board even when the system is turned off.)

3.

Expose both the card cage section and the power section of the system (see
Section 4.3).

4.

Remove the cable clip between the power section and the card cage section of the
system.

5.

Unplug the cable connection to the server feature module and thread the cable
through from the fan section into the card cage section. Leave the cable loose and
out of the way.

6.

Unplug the cable connections to the CPU(s) and thread them up to the top of the
card cage section above CPU0. Leave the cable loose and out of the way.

7.

Unplug the three cable connections to the system board; two connections on top
right corner of the board and one about 2 inches below the CPU1 slot on the right
of the board. Leave the cable loose and out of the way.

8.

Unplug the cable connection to the floppy and, if applicable, to the optional
device above the floppy. Again leave the cable loose and out of the way.

9.

Remove the power supply (see Section 4.9).

10.

Unplug the cable connection to the CD-ROM.

11.

Unplug the cable connections to the repeater card(s) and/or the StorageWorks
backplane.

12.

Unplug all the connections to the power transition module.

13.

As you remove the power harness from the system, be careful as you thread that
piece of the cable that passes from the power section into the card cage section
below the system board.

Replacement

Reverse the steps in the Removal procedure.

Verification

Power up the system.

«
...
109
110
111
112
113
...
»

Содержание AlphaServer DS20























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AlphaServer DS20

Altos R700 Series

Бренд: Acer Страницы: 80

Altos G700 series

Бренд: Acer Страницы: 14

Бренд: Acer Страницы: 103

Altos R720 Series

Бренд: Acer Страницы: 104

Z10 BUISNESS CLASS Z10 BC

Бренд: IBM Страницы: 67

x3450 - System - 7948

Бренд: IBM Страницы: 2

eServer BladeCenter JS20 Type 8842

Бренд: IBM Страницы: 150

SUPERO SuperServer 6026TT-GIBQRF

Бренд: Supero Страницы: 104

ES.2 - Barracuda Enterprise 750GB SATA/300 7200RPM 32MB Hard Drive

Бренд: Seagate Страницы: 2

Бренд: Quictent Страницы: 24

Бренд: Digisol Страницы: 81

Бренд: BELINEA Страницы: 53

Turbo Station TS-73AU Series

Бренд: QNAP Страницы: 69

Бренд: Seagate Страницы: 46

JetStream T2600G-28TS

Бренд: TP-Link Страницы: 1136

Бренд: Mobily Страницы: 12

Бренд: Matrix Switch Corporation Страницы: 60

Бренд: Stardom Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды