Compaq AlphaServer DS20 Скачать руководство пользователя страница 97

Страница: 97 / 182

Removal and Replacement

4-7

Exposing the System

CAUTION: Be sure the system On/Off button is in the “off” position before removing
system covers.

Shut down the operating system.

Press the On/Off button to turn the system off.

Unlock and open the door that exposes the storage shelf.

Pull down the top cover latch shown in Figure 4-2 until it latches in the down
position.

Grasp the finger groove at the rear of the top cover and pull it straight back about
2 inches and then lift it off the cabinet.

Pull a side panel back a few inches, tilt the top away from the machine, and lift it
off. (Repeat for the other side.)

From the back, removing the right side cover exposes the system card cage;
removing the left side cover exposes the power supply and SCSI backplane.

Dressing the System

Reverse the steps in the exposure process.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды

Compaq AlphaServer DS20, Руководство по обслуживанию

Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды