Compaq AlphaServer DS20 Скачать руководство пользователя страница 129

Страница: 129 / 182

Removal and Replacement

4-39

Removal

Shut down the operating system and turn the system off.

Unplug the AC power cords.

Expose the power section of the system (see Section 4.3).

Remove the power and signal cables from the UltraSCSI bus extender on the side
of the StorageWorks shelf.

Remove the power harness and all signal cables from the StorageWorks
backplane and the power transition module and lift it out of the way.

Using a short Phillips head screwdriver, remove the screws holding the backplane
to the back of the shelf and remove from the system.

Replacement

Reverse the steps in the Removal procedure.

Verification

Power up the system. Use the show device console command to verify that the
StorageWorks shelf is configured into the system.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды

Compaq AlphaServer DS20, Руководство по обслуживанию

Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды