Compaq AlphaServer DS20 Скачать руководство пользователя страница 121

Страница: 121 / 182

Removal and Replacement

4-31

Removal

Shut down the operating system and turn the system off.

Expose the card cage side of the system (see Section 4.3).

To remove the StorageWorks door:

Open the door slightly and grab the left edge of the door with your left hand
and the right edge of the door with your right hand.

While pushing the door up, bend it by pulling it away from the system. The

door compresses enough so its bottom post slips out of its retaining hole.

Once the bottom of the door is free, gently pull the top down to release it
from the post on the door jam and release it from the spring.

Put the door aside.

Using a Phillips head screwdriver, remove the nine screws holding the molded
plastic front panel to the system. (Six screws are accessed from the front of the
system and three through the fan compartment.)

Tilt the front panel away from the system and disconnect all the cables from the
OCP.

Once the front panel is removed, unscrew the four screws holding the OCP to the
front panel.

Replacement

Reverse the steps in the Removal procedure.

Verification

Power up the system. If the OCP you installed is faulty, the system will not power up.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды

Compaq AlphaServer DS20, Руководство по обслуживанию

Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Похожие инструкции для AlphaServer DS20

Бренды по названию

Популярные бренды