Compaq AlphaServer DS20 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 182

background image

System Overview

1-21

Table 1-1 PCI Slot Numbering

Slot

PCI0

PCI1

ISA

Shared

5

PCI to ISA bridge

ISA device

logically

6

Adaptec SCSI

7

PCI slot

PCI slot

8

PCI slot

PCI slot

9

PCI slot

PCI slot

ISA device

physically

The logic for two PCI buses is on the system board.

•

PCI0 is a 64-bit bus with three PCI slots, a Cypress chip, and an Adaptec SCSI
controller.  The Cypress chip is the PCI to ISA bus bridge and controls the
following: the keyboard, mouse, IDE bus, real-time clock, and the USB bus.  (The
IDE bus and the USB bus are not used.)  Connected to the ISA bus is an Adaptec
UltraSCSI controller with two ports (also not used).

•

PCI1 is a 64-bit bus with three PCI slots.

The cable connector to the floppy is on the system board.  Connectors for the mouse,
keyboard, and COM2 are on the bulkhead and are connected directly to the Cypress
chip.  The connector for COM1 is also on the bulkhead, but its path is from the
Cypress chip to the RCM connector out to the server feature module and back through
the RCM connector and then to the bulkhead.  The path to the OCP is also carried
through the RCM connector to the server feature module and then on to the OCP.

«
...
29
30
31
32
33
...
»

Содержание AlphaServer DS20























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AlphaServer DS20

8841 - eServer xSeries 236

Бренд: IBM Страницы: 100

NetVista N2800e

Бренд: IBM Страницы: 82

Бренд: Ubee Страницы: 9

Бренд: ADTRAN Страницы: 9

Elinx ESW200 Series

Бренд: B&B Electronics Страницы: 20

Бренд: 3Com Страницы: 32

Бренд: B&B Electronics Страницы: 2

Бренд: Matrix Switch Corporation Страницы: 60

SG-XPCIESAS-R-INT-Z

Бренд: Oracle Страницы: 148

Бренд: Axel Страницы: 28

Бренд: ADDON Страницы: 4

NetShare GX ME-752GNS

Бренд: welland Страницы: 3

SUPERSERVER 5017C-MF

Бренд: Supero Страницы: 96

GigaSpire BLAST u4hm

Бренд: Calix Страницы: 45

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

InTANK iR2775-S3

Бренд: Raidon Страницы: 2

Бренд: Wieland Страницы: 2

Бренд: SanDisk Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды