Compaq AlphaServer DS20 Скачать руководство пользователя страница 55

Страница: 55 / 182

Troubleshooting

2-5

Table 2-1 Control Panel Display

Content of Display

Progress Indicated in Power-Up Flow

Compaq

CPU functioning, path to the OCP operating. Hardware
involved – CPU, C-chip, P-chip 0, PCI to ISA bridge,
ISA to XBUS bridge, OCP controller.

Compaq *

B-cache initialized and both B-cache and memory is
being tested. Additional hardware involved: Backup
cache on the CPU module, D-chips, memory DIMMs.

Compaq Firmware

Firmware loading. Additional hardware involved – TIG
bus.

Compaq Error 06

Memory error. No memory was found, or memory is
bad, or misconfigured, or needs re-seating.

Probe I/O Subsystem

SRM console probing the system. Additional hardware
involved – P-chip 1, all devices on both PCIs.

AlphaServer DS20

Either the SRM console or AlphaBIOS are up and
running.

Содержание AlphaServer DS20























































































































































































Результаты поиска

Содержание AlphaServer DS20

Отзывы:

Compaq AlphaServer DS20, Руководство по обслуживанию, Страница: 55 / 182

Результаты поиска

Содержание AlphaServer DS20

Отзывы: