Compaq AlphaServer DS20 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 182

background image

Removal and Replacement

4-13

Removal

1.

Shut down the operating system and turn the system off.

2.

Unplug the AC power cord. (Auxiliary power is applied to the server feature
module and parts of the system board even when the system is turned off.)

3.

Expose the card cage side of the system (see Section 4.3).

4.

Remove memory.

5.

Remove all CPUs.

6.

Remove all PCI and ISA options.

7.

From the back of the cabinet, using a Phillips head screwdriver, unscrew the four
screws holding the CPU module brace from the system frame. Remove the brace.

8.

Unplug all cables connected to the system board and clear access to all screws
holding the system board in place.

9.

Using a Phillips head screwdriver, unscrew the fifteen screws holding the system
board in place and remove it from the system. Note the two guide studs, one in
the upper right corner and the other in the lower left corner, that protrude through
holes in the system board.

Replacement

Reverse the steps in the Removal procedure.

Verification

Power up the system (press the Halt button if necessary to bring up the SRM console)
and issue the show device command at the console prompt to verify that the system
sees all system options and peripherals.

«
...
101
102
103
104
105
...
»

Содержание AlphaServer DS20























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AlphaServer DS20

StorageLoader DLT VS160

Бренд: Tandberg Data Страницы: 13

StorageLoader DLT VS160

Бренд: Tandberg Data Страницы: 46

StorageLibrary LTO-3 SCSI

Бренд: Tandberg Data Страницы: 2

SDLT220-320 INTEGRATION

Бренд: Tandberg Data Страницы: 142

Бренд: Tandberg Data Страницы: 3

Бренд: Tandberg Data Страницы: 12

Firebox SOHO 6 Wireless

Бренд: Watchguard Страницы: 8

Бренд: Seagate Страницы: 57

TOWERRAID TR5M1

Бренд: Sans Digital Страницы: 82

Barracuda 7200.7 ST3120025A

Бренд: Seagate Страницы: 58

Vlinx Serial Servers ESP901E

Бренд: B&B Electronics Страницы: 92

System Storage N3150

Бренд: IBM Страницы: 24

Бренд: SAGEMCOM Страницы: 75

FusionServer CH242 V5

Бренд: xFusion Digital Technologies Страницы: 61

Бренд: IBM Страницы: 51

Бренд: G-Technology Страницы: 33

Бренд: LaCie Страницы: 22

Бренд: 360 Systems Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды