background image

Safety 

Sea Tel Tracker 6000

 

 
 
 

 

1.

 

Safety

 

 

The following general safety precautions must be observed during all phases of operation, service and repair 
of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual 

violates safety standards of design, manufacture and intended use of the equipment.  Sea Tel Inc (dba 

Cobham SATCOM) assumes no liability for the customer's failure to comply with these requirements. 

Service

 

Access to the interior of the Out Door Unit (ODU), is allowed for inspection of components by a 

technician/engineer.  Maintenance of the ODU should only be performed by technicians/engineers who 

are authorized by Cobham SATCOM.  Only authorized Partners who have received factory training on 
this equipment will be able to file a claim for warranty reimbursement.  Failure to comply with standard 
practices, which include but are not limited to modification of the terminal away from factory 

documented assemblies may also void the warranty period. 

Do not service or adjust alone

 

Do not attempt internal service or adjustments unless another person, capable of rendering first aid 
resuscitation, is present. 

Personal Protection Equipment (PPE):

 

Hard hat, safety glasses and steel toe work boots are required. 
To avoid injuries, it is important to be aware of the risks present when handling and testing an antenna 

from inside the dome.  There is a risk of the antenna injuring the operator, as the antenna moves, so 
the operator must be aware of the position of the antenna at all times while inside the radome. 

Grounding, cables and connections

 

To minimize shock hazard and to protect against lightning, the equipment chassis and cabinet must be 

connected to an electrical ground.  The ODU equipment must be grounded to a known good earth 
ground.  For further grounding information refer to the Installation chapter of this manual. 
Do not extend the cables beyond the lengths specified for the equipment.  The cables between the ODU 

and the Baseband Equipment Rack must comply with the specified data concerning cable losses etc. 

Power supply

 

AC Power to the ADE is provided by a separate, breakered, power source. 

Do not operate in an explosive atmosphere

 

Do not operate the equipment in the presence of flammable gases or fumes.  Operation of any electrical 
equipment in such an environment constitutes a definite safety hazard. 

Keep away from live circuits

 

Operating personnel must not remove equipment covers.  Component replacement and internal 

adjustment must be made by qualified maintenance personnel.  Do not replace components with the 

power cable connected.  Under certain conditions, dangerous voltages may exist even with the power 

cable removed.  To avoid injuries, always disconnect power and discharge circuits before touching them. 

SAFETY:  INTERNAL BATTERY

 

The main PCB inside the TICU contains a lithium battery.  These batteries should last for many years but 

if replacement is required, use caution.  These batteries are only to be replaced by a technician 

authorized by Cobham SATCOM to perform such service. 

 

 

 

Failure to comply with the rules above will void the warranty!

 

 

 

 

 

1‐1 

EAR Controlled  -  ECCN  EAR99

 

CAUTION  -  

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. 

DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 

Содержание Sea Tel Tracker 6000






















































Отзывы: