Citel EXTender 1100 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 104

Citel EXTender 1100 Скачать руководство пользователя страница 34

EXTender 1100A Switch and Remote Module System Administrator’s

Guide

34

Essential Configuration - Quick Reference

This section is a quick reference list of the essential configuration steps that must be
performed during the execution of the Setup Wizard and/or after the Setup Wizard has
been run to ensure proper functionality of the units. A full description of the features
described below begins with the

Essential Configuration – Switch Module

section later in

this document.

1. Set the Region Code. This is the Country the unit will be operating in. See the Switch

Module – Essential Setup Wizard Configuration and Remote Module – Essential
Setup Wizard configuration sections for full details.

Only configurable using Setup Wizard.

Path:

Gateway (and Remote)->Utilities->Setup_Wizard

►

Refer to page

xx and yy

for full details.

2. Set the PBX Type. This is the phone protocol the unit will be using. See the Switch

Module – Essential Setup Wizard Configuration and Remote Module – Essential
Setup Wizard configuration sections for full details.

Only configurable using Setup Wizard.

Path:

Gateway (and Remote)->Utilities->Setup_Wizard

►

Refer to page

xx and yy

for full details.

3. Set the Telco type, dialup or leased line operation. Configure the Modem Settings for

communication between the Switch and Remote Module. See the Switch Module

Essential Connect Parameters - Modem Settings

and the Remote Module Essential

Connect Parameters sections for full details.

Path:

Gateway(and Remote)->Configuration->Connect->Modem_Settings

TMI Path:

(Remote Only)->Set Config->Modem Menu->Leased Line

►

Refer to page

39

and yy for full details.

4. Set the Dial Numbers for the Remote Module (If Leased Line is disabled). These are

the phone numbers of the analog telephone lines connected to the Switch and
Remote Modules. See the Remote Module

Essential Connect Parameters – Dial

Numbers

for full details.

Path:

Remote->Configuration->Connect->Dial_Numbers

TMI Path:

(Remote Only)->Set Config->Connect Menu->Office Number

►

Refer to page

42

for full details.

5. Set the User ID on Remote Side. It is recommended but not required to set the

Remote User ID, if not configured you will be prompted to enter User ID on each
connect to Switch Module. The default User ID is 1 on Switch side. See the Remote
Module

Advanced Port Setup

for full details.

Path:

Remote->Configuration->Port->User_ID

TMI Path:

(Remote Only)->Set Config->Connect Menu->User ID

►

Refer to page

xx

for full details.

Document Number: M-1100A-MUC

Version: Rev AG

© Copyright 2008 Citel plc All Rights Reserved

«
...
32
33
34
35
36
...
»

Содержание EXTender 1100









































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды