Cisco SFS 3504 Скачать руководство пользователя страница 69

Страница: 69 / 82

5-5

Cisco SFS 3504 Multifabric Server Switch Hardware Installation Guide

OL-14325-01

Chapter 5 Cisco SFS 3504 Server Switch LEDs

Fibre Channel Gateway LEDs

Fibre Channel Gateway Card Status LEDs

Each Fibre Channel gateway card includes two LEDs (one green and one yellow) as shown in

Figure 5-2

These indicators describe the Fibre Channel card status. The OK label is for the green LED, and
the ! label is for the yellow LED.

Table 5-4

describes the Fibre Channel gateway card LED indicators.

Fibre Channel Gateway Port Status LEDs

Two LEDs are provided for each Fibre Channel port on each Fibre Channel gateway card. The LEDs
indicate status/activity and speed (see

Figure 5-2

Table 5-5

describes the Fibre Channel port status

LED indicators. The Link status indicator is a green LED, and the Fault indicator is a yellow LED.

Table 5-4

Fibre Channel Card Status LED Indicators

LEDs

Indicators

OK Label

! Label

Off

Gateway card power not enabled, LED failure, or power
failure

Fast Blink

Off

Gateway card initializing after power on or reset

Off

Gateway card operational with no errors detected

Off

Gateway card error detected: power, temperature, or
electronics. Operator intervention is required.

Slow blink

LED test following power on: Both LEDs blink slowly
(1/4 Hz.)

Off

Fast Blink

Identify the gateway card by causing it to blink by using the
CLI

Table 5-5

Fibre Channel Port Status LED Indicators

LEDs

Indicators

Link Label

Fault Label

Off

Port operational and active with attached node

Blinking
(1/2 second)

Set to beaconing, active with attached node

Off

Port operational but not communicating with attached node

Off

Port failure

Off

Blinking
(1/2 second)

Set to beaconing

Blinking
(1/8 second)

Off

Active communication (exchange of Fibre Channel frames)

Blinking
(1/8 second)

Blinking
(1/2 second)

Set to beaconing and active communication

Port failure

Содержание SFS 3504



















































































Результаты поиска

Содержание SFS 3504

Отзывы:

Похожие инструкции для SFS 3504

Бренды по названию

Популярные бренды

Cisco SFS 3504, Руководство по установке оборудования

Результаты поиска

Содержание SFS 3504

Отзывы:

Похожие инструкции для SFS 3504

Бренды по названию

Популярные бренды