manualshive.com logo in svg

Cisco MX200 G2, Руководство администратора

Поделиться
Скачать
Cisco MX200 G2 Скачать руководство пользователя страница 81

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.  

www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 

81

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Network [1] IEEE8021X Eap Peap

Define the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN 

clients without the need for client certificates. Developed by Microsoft, Cisco and RSA 

Security.

Requires user role: ADMIN
Default value: On

Value space: Off/On

Off: The EAP-PEAP protocol is disabled.
On: The EAP-PEAP protocol is enabled (default).

Network [1] IPStack

Select if the system should use IPv4, IPv6, or dual IP stack, on the network interface. NOTE: 

After changing this setting you may have to wait up to 30 seconds before it takes effect.

Requires user role: ADMIN
Default value: Dual

Value space: Dual/IPv4/IPv6

Dual: When set to Dual, the network interface can operate on both IP versions at the 

same time, and can have both an IPv4 and an IPv6 address at the same time.
IPv4: When set to IPv4, the system will use IPv4 on the network interface.
IPv6: When set to IPv6, the system will use IPv6 on the network interface.

Network [1] IPv4 Assignment

Define how the system will obtain its IPv4 address, subnet mask and gateway address. This 

setting only applies to systems on IPv4 networks.

Requires user role: ADMIN
Default value: DHCP

Value space: Static/DHCP

Static: The addresses must be configured manually using the Network IPv4 Address, 

Network IPv4 Gateway and Network IPv4 SubnetMask settings (static addresses).
DHCP: The system addresses are automatically assigned by the DHCP server.

Network [1] IPv4 Address

Define the static IPv4 network address for the system. Applicable only when Network IPv4 

Assignment is set to Static.

Requires user role: ADMIN
Default value: ""

Value space: String (0, 64)

A valid IPv4 address.

Network [1] IPv4 Gateway

Define the IPv4 network gateway address. Applicable only when the Network IPv4 

Assignment is set to Static.

Requires user role: ADMIN
Default value: ""

Value space: String (0, 64)

A valid IPv4 address.

Network [1] IPv4 SubnetMask

Define the IPv4 network subnet mask. Applicable only when the Network IPv4 Assignment 

is set to Static.

Requires user role: ADMIN
Default value: ""

Value space: String (0, 64)

A valid IPv4 address.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices

System settings

Содержание MX200 G2














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды